Sub-station

MPS

Nylon rods of the mechanical vibration and abrasion resistance

by:MPS     2020-10-06

nylon rods with good toughness, wear resistance, oil resistance, seismic, tensile strength, flexural strength, water absorption, good dimensional stability, which is used for processing all kinds of high strength wear-resistant parts. Nylon rods widely used, is a plastic instead of steel, iron, copper and other metal materials, is an important engineering plastics, cast nylon widely instead of mechanical equipment wear parts, instead of copper and the alloy wear-resistant parts.

the spindle of the nylon rods at both ends are equipped with coat and roll head, and all have the same slot, to match the slider. The width of the slot to 50 mm, deep 18. 5 mm, this is known as the slider and coat in the shaft are exposed to maximum upward long variable values, on which a to deliver significant torque. The spindle with nylon rods pin coat the start-stop action card ring ( One at each end) , it is two and a half ring through a hinge, bolted.

nylon rods mechanical strength, stiffness, hardness, high toughness, good ageing resistance, good mechanical damping capacity, good sliding resistance, excellent wear resistance, good machining performance, when used for precision control, no creep phenomenon, anti-wear performance good, good dimensional stability. If you have needs, can communicate with me by phone manufacturers contact.

nylon rod has good toughness and wear resistance force, oil resistant, seismic, tensile, bending strength, and has the characteristics of small water absorption, good dimensional stability, and is used for processing various wear-resistant high strength parts. So, what kind of common nylon rods are there?

1, nylon 4. 6 ( Red brown) 4: compared with the ordinary nylon, nylon. 6 is the feature of rigid save power, good resistance to creep, in a wider temperature range, more heat aging, therefore, nylon 4. 6 for nylon 6, nylon 66, POM and PET in stiffness, creep and thermal aging, fatigue strength and wear resistance can not meet the requirements of the temperature field of the 'high' ( 80 - 150 ℃) 。

2, nylon 6 ( White) : the material has the most excellent comprehensive performance, including mechanical strength, stiffness, toughness, mechanical vibration and abrasion resistance. These features, coupled with good electrical insulating ability and chemical resistance, make the nylon 6 as a 'universal' materials, used in the mechanical structure parts and maintainable parts manufacturing.

3, nylon 66 ( Cream) : compared with nylon 6, the mechanical strength, rigidity, heat resistance and abrasion resistance, creep resistance is better, but the impact strength and mechanical damping performance degradation, is very suitable for the automatic lathe machining.

4, nylon 66 + MOS2 ( A film) : this kind of nylon add the molybdenum disulfide, compared with nylon 66, its rigidity, hardness and size stability has improved, but the impact strength declined, molybdenum disulfide grain formation effect improves the crystalline structure, bearing materials and wear-resisting performance are improved.

5, nylon 66 + GF30 ( Black) : compared with the pure nylon 66, nylon add this 30% glass fiber reinforced, heat resistance, strength and stiffness. Creep resistance and dimensional stability, wear-resisting performance were increased, the maximum allowable temperature is higher.

4 nylon. 6 ( Red brown) 4: compared with the ordinary nylon, nylon. 6 is the feature of rigid save power, good resistance to creep, in a wider temperature range, more heat aging, therefore, nylon 4. 6 for nylon 6, nylon 66, POM and PET in stiffness, creep and thermal aging, fatigue strength and wear resistance can not meet the requirements of the temperature field of the 'high' ( 80 - 150 ℃) Nylon 6 (

White) : the comprehensive performance of the material has, including mechanical strength, stiffness, toughness, mechanical vibration and abrasion resistance. These features, coupled with good electrical insulating ability and chemical resistance, make the nylon 6 as a 'universal' materials, used in the mechanical structure parts and maintainable parts manufacturing. Nylon 66 (

Cream) : compared with nylon 6, the mechanical strength, rigidity, heat resistance and abrasion resistance, creep resistance is better, but the impact strength and mechanical damping performance degradation, is very suitable for the automatic lathe machining.

nylon 66 + GF30 ( Black) : compared with the pure nylon 66, nylon add this 30% glass fiber reinforced, heat resistance, strength and stiffness. Creep resistance and dimensional stability, wear-resisting performance were increased, allows the use of higher temperature.

nylon 66 + MOS2 ( A film) : this kind of nylon add the molybdenum disulfide, compared with nylon 66, its rigidity, hardness and size stability has improved, but the impact strength declined, molybdenum disulfide grain formation effect improves the crystalline structure, bearing materials and wear-resisting performance are improved.

this website: https://www. 国会议员, insulationpins。 com/news/573。 HTML keywords: nylon rods
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...